manualshive.com logo in svg

Siemens VDO DTCO 1381, Техническое описание

Поделиться
Скачать
Siemens VDO DTCO 1381 Скачать руководство пользователя страница 185

Service only

First calibration

10.2 Calibration instructions

Edition 07/2007

Technical Description DTCO 1381

10 - 7

TD00.1381.00 13

2 102

10.2.3 Programming the UTC time

Before activating the DTCO 1381 as the EU control device, unre-
stricted programming of the UTC time is possible.

After activation of the DTCO 1381 and one-off programming of the 
UTC time, this function is blocked for security reasons. The 
workshop card must then be removed and re-inserted; i.e, the 
workshop card must be re-authenticated.

10.2.4 Parameter measurements

Before the parameter measurements

 – in particular the character-

istic coefficient (w-value) – the following must be checked:

1.

Check whether all cables – in particular the KITAS sensor cable – 
are undamaged.

2.

Check whether the KITAS sensor cable is connected directly, i.e. 
without branchings, at DTCO 1381 and KITAS 2171.

After the parameter measurements

 and programming – in par-

ticular the characteristic coefficient (w-value) – the following must 
be checked:

3.

Check whether the DTCO 1381 displayed or saved any sensor 
faults.

4.

Check whether the programmed and saved parameters are 
according to the beforehand measured parameters.

Please refer to the testing device instructions for information on 
how to prepare for and execute the parameter measurements.

If one of the above-mentioned points is not fulfilled, locate the 
cause and repeat the measurement.

Содержание VDO DTCO 1381















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды