manualshive.com logo in svg

Siemens VDO DTCO 1381, Техническое описание

Поделиться
Скачать
Siemens VDO DTCO 1381 Скачать руководство пользователя страница 113

Service only

Installation

5.2 Instructions on installing the DTCO 1381

Edition 07/2007

Technical Description DTCO 1381

5 - 9

TD00.1381.00 13

2 102

5.2.2 Working on the electrical onboard power supply

5.2.3 Laying and establishing connecting cables

Caution! Danger of short circuits

Before working on the onboard power supply, please observe the 
relevant manufacturer's instructions!

•

Although disconnection of the vehicle’s battery will prevent 
short circuits, this may also result in other secondary effects: 
– The security code of the vehicle’s radio may be deleted.
– If intelligent systems are installed, their data (like the error 

memory of the motor controller) may be deleted.

•

Before disconnecting the connection terminals from the battery, 
observe the following points:
– Switch off all electrical consumers.
– Separate the minus and plus terminals.

Caution! Danger of fire due to short circuit

Damaged cables can cause short circuits, undesired interferences, or 
disturbances.

Please observe the following:

•

Always observe the information provided by the vehicle manu-
facturer.

•

Lay the lines in such a way that they are not subjected to tensile 
or shearing force or pressure.

•

Properly fit the cables into place using tape or cable binders.

•

Do not route the cable around moving parts. Use rubber sleeves 
as protection when feeding a cable through metal or plastic 
parts.

•

Replace damaged cables immediately!

Содержание VDO DTCO 1381















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды