Siemens SIREMOBIL Compact L Скачать руководство пользователя страница 78

Страница: 78 / 86

SIREMOBIL Compact

SPR2-130.061.02

Page 26 of 28

Siemens AG

System Manual

Rev. 11

09.04

CS PS 24

Medical Solutions

6 - 26

Replacing boards / replacing components

MULTISPOT 2000

Before installing the new MULTISPOT 2000, set the correct refresh rate.

•

Disconnect the SIREMOBIL Compact line voltage plug from the receptacle.

•

Replace the MULTISPOT 2000.

•

The screws securing the MULTISPOT 2000 are accessible on the underside of the cam-
era.

•

Perform a camera function test after the replacement.

•

Generate and program the exposure parameters for the MULTISPOT 2000 according to
the IQ Quick test (refer to the log book). Record the new exposure parameters in the
IQ Quick test instructions.

Area dose product measurement device

•

Remove the SIREPHOS cover (see Chapter 1, "Covers").

•

Replace the electronics board and the dose measurement chamber.

•

Perform the calibration of the area/dose product measurement device.
Refer to Chapter 5 "Calibrating the Area Dose Product Measurement".

•

Test the accuracy of the area dose product measurement device. Refer to Chapter 5
"Testing the accuracy of the area dose product measurement device".

•

Re-attach the SIREPHOS cover.

•

Seal the SIREPHOS cover using sealing compound (see Chapter 1, "Covers").

Electrical voltage!
See Chapter 1, Safety Information.

Switch the system power supply off and disconnect the power
plug.

50 Hz refresh rate

60 Hz refresh rate

Jumper

Position

Jumper

Position

open

X10

X11

Tab. 1

WARNING

Содержание SIREMOBIL Compact L























































































Результаты поиска

Содержание SIREMOBIL Compact L

Отзывы:

Siemens SIREMOBIL Compact L, Инструкция по эксплуатации, Страница: 78 / 86

Результаты поиска

Содержание SIREMOBIL Compact L

Отзывы: