Siemens SIREMOBIL Compact L Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 86

Siemens SIREMOBIL Compact L Скачать руководство пользователя страница 60

SIREMOBIL Compact

SPR2-130.061.02

Page 8 of 28

Siemens AG

System Manual

Rev. 11

09.04

CS PS 24

Medical Solutions

6 - 8

Replacing boards / replacing components

•

Remove the Compact optics.

•

To do this, pull the anode cable out of the Compact optics recess.

•

Rotate the C-arm so that the I.I. is underneath and the tube assembly above.

•

Remove the attachment screws from the I.I. mounting. When doing this, hold onto the I.I.
(5/Fig. 2).

•

Remove the I.I. from the mounting.

Installing the new I.I.

6

•

Prior to installing the new I.I. on the C-arm mounting, complete the following work.

•

Reinstall the Compact optics on the new I.I.
- When doing this, feed the anode cable through the recess in the optics.

The Compact optics must sit adjacent to the eccentric screws.

•

Move the camera rotation of the Compact optics to the zero position.
- To do this, connect the ohmmeter to the potentiometer for camera rotation, position 2

and 3 (5/Fig. 3).
A resistance value of 5000 ohms, + 40 ohms must be measured for the center position.

- Hold the camera rotation by the clamp ring (1/Fig. 3) and turn it to the correct position, if

necessary.

•

Place the VIDEOMED DC in the zero position on the Compact optics (6/Fig. 2) and
clamp it in place.

•

Connect the cable from the VIDEOMED DC to the Compact optics and secure it with ca-
ble ties.
Make sure that the cable lies in the recess of the VIDEOMED DC board and does not
protrude past the edge of the board.

•

Install the new control section included in the I.I. delivery volume.

•

Connect cables E1, E2.

•

Secure the new I.I. to the mounting with the screw.
- The I.I. can be swivelled slightly to the side to permit easier cable routing.

•

Route the cables for the high voltage section back through the recess in the I.I.
(3/Fig. 1 or 3/Fig. 4).

•

Swivel the I.I. back again.
- When doing this, make sure that all the cables are correctly positioned.

•

Secure the I.I. on the mounting (5/Fig. 2).

Risk of crushing!
Noncompliance can cause damage to property.

Apply all C-arm brakes and hold the I.I. when removing the attach-
ment screws.

When installing the Compact optics and the VIDEOMED DC, make
sure that no dust or dirt contaminates the I.I. output window or
the Compact optics.

CAUTION

NOTE

«
...
58
59
60
61
62
...
»

Содержание SIREMOBIL Compact L























































































Отзывы:

Нет отзывов