Siemens SINAMICS G12 Скачать руководство пользователя страница 54

Страница: 54 / 160

Additional requirements placed on the protective conductor

①

● For permanent connection, the protective conductor must fulfill at least one of the following

conditions:
– The protective conductor is routed so that it is protected against damage along its

complete length.

Cables routed inside switch cabinets or enclosed machine housings are considered to

be adequately protected against mechanical damage.

– As a conductor of a multi-conductor cable, the protective conductor has a cross-section

≥ 2.5 mm² Cu.

– For an individual conductor, the protective conductor has a cross-section ≥ 10 mm² Cu.
– The protective conductor consists of two individual conductors with the same cross-

section.

● When connecting a multi-core cable using an industrial plug connector according to EN

60309, the protective conductor must have a cross-section of ≥ 2.5 mm² Cu.

Connecting-up
5.1 Permissible line supplies

Power Module PM240-2

Hardware Installation Manual, 08/2017, A5E33294624B AG

Содержание SINAMICS G12

































































































































































Результаты поиска

Содержание SINAMICS G12

Отзывы:

Siemens SINAMICS G12, Руководство по установке оборудования, Страница: 54 / 160

Результаты поиска

Содержание SINAMICS G12

Отзывы: