Siemens SIMATIC TDC Скачать руководство пользователя страница 30

Страница: 30 / 228

Installation and EMC guidelines

1.14 Power supply

SIMATIC TDC hardware

System Manual, 08/2017, A5E01114865-AL

Air intake temperature

The maximum air intake temperature on the SIMATIC TDC may not be exceeded. The

following limits are valid, depending on the "shutdown mode" switch setting.

Shutdown mode

Maximum air intake temperature up to 2000 m above

sea level

ONE / ON

Shutdown on fan failure

60° Centigrade

TWO / OFF

Shutdown on failure of two fans

35° Centigrade

1.14

Power supply

Measures against disturbance voltages

The following notes related to the EMI/EMC measures to take for systems/plants should be

observed in order to avoid disturbance peaks on the supply cables in the cabinet:

Interference suppression on mains

The power supply of the rack already has a line filter with sufficient attenuation (refer to

"Manufacturers declaration").
For more demanding applications, you can install an additional line filter (e.g. 250 V AC /

10 A) or overvoltage arrester in the mains line, as close as possible to the cable entry on the

cabinet. Ground of the line filter/arrester must be wired to the equipotential busbar of the

cabinet using the shortest possible conductor length.

24 V power supply

To attenuate external interference, a line filter must be provided for the 24 V power supply of

the digital I/O (e.g. SIFI-B line filter, Order No. B84112-B-.... from Epcos/NF 1-1 line filter of

Phoenix Contact). This filter should be installed as close as possible to the terminal block.

The shield connections of the line filter must be bonded to ground across the shortest

possible distance.
The 24 V power supply must also be equipped with lightning/overvoltage protection.
For more information, refer to the installation manual "SIMATIC Automation Systems

S7-400, Hardware and Installation

(

http://support.automation.siemens.com/WW/view/de/1117849/0/en

)".

NOTICE
Network devices
Safe electrical isolation to IEC 61131-2 IEC 61131-2 (11.1.2.1.3) must be ensured for all

power supply units operated on SIMATIC TDC devices and modules.

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Содержание SIMATIC TDC





































































































































































































































Результаты поиска

Содержание SIMATIC TDC

Отзывы:

Похожие инструкции для SIMATIC TDC

Бренды по названию

Популярные бренды

Siemens SIMATIC TDC, Системное руководство

Результаты поиска

Содержание SIMATIC TDC

Отзывы:

Похожие инструкции для SIMATIC TDC

Бренды по названию

Популярные бренды