Siemens SIMATIC TDC Скачать руководство пользователя страница 58

Страница: 58 / 228

Rack

3.2 Rack UR5213 (6DD1682-0CH2)

SIMATIC TDC hardware

System Manual, 08/2017, A5E01114865-AL

3.2.7

Voltage monitoring

Input voltage

The input voltage is monitored for low level.

Input voltage

Reaction

Undervoltage < approx. 85 V

ACFAIL signal and CPU STOP, shutdown of

output voltages <85V

Voltage dips ≤ 20 ms are buffered.

The power supply unit and therefore the system are restarted automatically on recovery from

a voltage dip below the permissible mains voltage.
The power on/off sequence (e.g. generation of a RESET or SYSFAIL signal) corresponds to

the reaction to manual operation of the mains switch.

Output voltage

All output voltages are monitored (e.g. for overload/short-circuit).

Voltage monitoring functions at the power supply

outlet

Reaction

+5 V in the range from 4.75 V to 5.35 V

“POWER OK” LED is lit green;

+ 3.3 V in the range from +3.18 V... +3.5 V
+ 12 V in the range from +11 V to +13 V
- 12 V in the range from -11 V to -13 V

In all other cases, the “POWER OK” LED is lit red.

System failure alarm

Select the "Object properties" in the "STOP" tab of HWConfig to configure the response of

the relevant module to a system failure alarm (bus signal *SYSFAIL=low):

●

Modules can reset their digital and analog outputs

●

CPU modules can go into the "STOP" state ("H" is displayed permanently)

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Содержание SIMATIC TDC





































































































































































































































Результаты поиска

Содержание SIMATIC TDC

Отзывы:

Похожие инструкции для SIMATIC TDC

Бренды по названию

Популярные бренды

Siemens SIMATIC TDC, Системное руководство

Результаты поиска

Содержание SIMATIC TDC

Отзывы:

Похожие инструкции для SIMATIC TDC

Бренды по названию

Популярные бренды