Siemens SIMATIC TDC Скачать руководство пользователя страница 205

Страница: 205 / 228

Interface module

7.5 Interface module SB71

SIMATIC TDC hardware
System Manual, 08/2017, A5E01114865-AL

205

Green LED

The voltage supply on SIMATIC TDC side is indicated by a green LED (P).

Red LED

The supply voltage on SIMATIC TDC side (1P, 1M) is short-circuited (fault).

Voltage supply on plant side

The 24/48 V DC power supply voltage for signals on plant side is wired to terminal block X4:

Terminal X4

Voltage on plant side

+24/48 V

0 V

Connect the cables using accessory kit SM11 "Power supply connector for interface

modules" (article number: 6DD1680-0BB0)
The maximum conductor cross-section at terminal X4 is 2.5 mm².

Test socket

The SIMATIC TDC supply voltage is available on the double test socket X5 (G; +):

Double test socket X5

Voltage SIMATIC side

+ (1P of X3)

G (1M of X3)

+24 V

0 V

WARNING

Explosion hazard
It is not allowed to use the X5 test sockets in potentially explosive environments.

Note
When wiring the supply voltage, observe the “Installation and EMC Directives” chapter in the

User Manual.

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Содержание SIMATIC TDC





































































































































































































































Результаты поиска

Содержание SIMATIC TDC

Отзывы:

Похожие инструкции для SIMATIC TDC

Бренды по названию

Популярные бренды

Siemens SIMATIC TDC, Системное руководство

Результаты поиска

Содержание SIMATIC TDC

Отзывы:

Похожие инструкции для SIMATIC TDC

Бренды по названию

Популярные бренды