Siemens SIMATIC TDC Скачать руководство пользователя страница 76

Страница: 76 / 228

CPU modules

4.1 CPU module CPU555

SIMATIC TDC hardware

System Manual, 08/2017, A5E01114865-AL

Note
Note the following for operation with modules:

•

Operation of the CPU555 with the CP5100 and CP50M0 modules that are being phased

out is not possible.

•

Use of a CP50M1 in combination with a CPU555 is only possible as of a firmware version

≥ 4

•

Use of a CP51M1 in combination with a CPU555 is only possible as of a functional status

≥ 8

•

Use of a CP52A0 with article number 6DD1660-0BH0 in combination with a CPU555 is

only possible as of a functional status ≥ 9

•

Use of a CP53M0 in combination with a CPU555 is only possible as of a functional status

≥ 9

•

Use of an SM500 in combination with a CPU555 is only possible as of a functional status

≥ 13

4.1.2

Control and display elements

LED display

The processor number, states and faults are displayed using a 5x7 dot matrix LED array.

Acknowledge button S1

This button has two functions:

●

Clearing the fault display:
The acknowledge button can be used to clear sporadic or non-critical fault displays on the

5x7 dot matrix LED. An additional fault is displayed after the first one has been

acknowledged.

●

Digital signal input can be evaluated using the ASI function block.

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Содержание SIMATIC TDC





































































































































































































































Результаты поиска

Содержание SIMATIC TDC

Отзывы:

Похожие инструкции для SIMATIC TDC

Бренды по названию

Популярные бренды

Siemens SIMATIC TDC, Системное руководство

Результаты поиска

Содержание SIMATIC TDC

Отзывы:

Похожие инструкции для SIMATIC TDC

Бренды по названию

Популярные бренды