manualshive.com logo in svg

Siemens SIMATIC TDC, Системное руководство

Поделиться
Скачать
Siemens SIMATIC TDC Скачать руководство пользователя страница 61

 

Rack 

 

3.2 Rack UR5213 (6DD1682-0CH2) 

SIMATIC TDC hardware 
System Manual, 08/2017, A5E01114865-AL 

61

 

3.2.11

 

Ventilation/cooling 

The rack is equipped with three fans for forced convection of the modules and with one fan 

for the system power supply.   
Since the rack is not equipped with an air filter, you should provide a filter on the cabinet if 

necessary. 

 

 

Note 
For more information, refer to section "Equipotential bonding (Page 22)". 

 

Fan monitoring 

The fans are monitored (speed). Activation of the monitoring function is delayed in order to 

enable the reliable startup of the rack after you switched on power. 
On failure of one or two fans, the power supply is shut down depending on the operating 

mode in order to prevent thermal destruction of the modules. 
Select the operating mode (SHUTDOWN MODE) using switch S1.4 that is integrated in the 

power supply. The power supply is shut down if one fan has failed and switch position "ON" 

is set, or if two fans have failed and switch position "OFF" is set. 
To set switch S1, unscrew the front panel and slightly pull it forward until you can reach the 

switch through the gap. Switch off power to the rack before you open the panel. 

 

 

WARNING 

Switch off power to the rack before you remove the front panel screws. 

 

 

CAUTION 

Observe the corresponding ESD Directives. 

 

The operating mode setting is indicated by the "SHUTDOWN MODE" LED on the front 

panel. 
Refer to chapter “Status and fault displays”. 

 

 

WARNING 

Always set the “Shutdown mode” dip switch S1.4 to “ON” for modules requiring forced 

convection (e.g. CPU551) at air intake temperatures from 0  C to 60 °C. 
You may only set the position of switch S1.4 to "OFF” if it can be assured that the air intake 

temperature at the rack does not exceed 35 °C. 
The power supply is not shut down on failure of a single fan, but the corresponding 

backplane bus signal (FANAL*) is activated and can be detected by the configuration 

software. 

 

Aotewell Ltd 

www.aotewell.com 

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Содержание SIMATIC TDC





































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды