Siemens SIMATIC TDC Скачать руководство пользователя страница 38

Страница: 38 / 228

General technical specifications

2.4 Mechanical requirements

SIMATIC TDC hardware

System Manual, 08/2017, A5E01114865-AL

2.4

Mechanical requirements

The following table provides information on the type and scope of checks regarding

mechanical ambient conditions.

Tested for

Test standard

Note

Vibrations

Vibration test according to

IEC 60068-2-6 (sine)

Type of vibration: Frequency cycles with a rate of change of 1

octave/minute
10

Hz ≤ f ≤ 58

Hz, constant amplitude 0.075 mm

Hz ≤ f ≤ 150

Hz, constant acceleration 1 g

Duration of vibration: 10 frequency cycles per axis in each of the

3 axes which are perpendicular to each other

Shock

Shock test according to

IEC 60068-2-27

Type of shock: half-sine
Strength of shock: 15 g peak value, 11 ms duration
Shock direction: 3 shocks each in +/– direction in each of the

three perpendicular axes

2.5

Electromagnetic requirements (industry)

Interference emission

EN 61000-6-4 : 2007 + A1:2011

Immunity to interference

EN 61000-6-2 : 2005

NOTICE
Using two-way radios and mobile telephones
The use of two-way radios and mobile phones in the immediate range of SIMATIC TDC can

influence the operation of the device.

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Содержание SIMATIC TDC





































































































































































































































Результаты поиска

Содержание SIMATIC TDC

Отзывы:

Похожие инструкции для SIMATIC TDC

Бренды по названию

Популярные бренды

Siemens SIMATIC TDC, Системное руководство

Результаты поиска

Содержание SIMATIC TDC

Отзывы:

Похожие инструкции для SIMATIC TDC

Бренды по названию

Популярные бренды