Siemens SIMATIC TDC Скачать руководство пользователя страница 29

Страница: 29 / 228

Installation and EMC guidelines

1.13 Power losses in the control cabinet

SIMATIC TDC hardware
System Manual, 08/2017, A5E01114865-AL

1.13

Power losses in the control cabinet

The dissipation capability of a cabinet and therefore the air intake temperature of the rack

depends on the type of cabinet, on the ambient temperatures and on the internal

arrangement of the devices.

Built-in versions

Frame / panel

Control cabinet (open) with

open-circuit ventilation
Air vents > 600 cm²

Cabinet (closed) with

intrinsic convection and

forced convection

Closed cabinet with

heat exchanger

For installation variants 1) and 2), it is presumed that there is a clearance of at least 1 meter

between the top of the control cabinet and the building's ceiling.

SHUTDOWN MODE

Using the SHUTDOWN MODE switch the user can select whether to shut down the rack

immediately on failure of the first fan, or not until an additional fan failure.

Shutdown mode

ONE / ON

Shutdown is initiated upon the failure of one fan

TWO / OFF

Shutdown is initiated upon the failure of one or more fans

For additional rack-specific information see:
UR6021 (6DD1682-0CH3) Control and display elements (Page 41)
UR5213 (6DD1682-0CH2) Control and display elements (Page 55)
UR5213 (6DD1682-0CH0) Control and display elements (Page 67)

Note
In the SHUTDOWN MODE, the internal output voltages of the rack are switched off. External

voltages connected to the module input must be switched off simultaneously (refer to section

Machinery directive (Page 17)).

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Содержание SIMATIC TDC





































































































































































































































Результаты поиска

Содержание SIMATIC TDC

Отзывы:

Похожие инструкции для SIMATIC TDC

Бренды по названию

Популярные бренды

Siemens SIMATIC TDC, Системное руководство

Результаты поиска

Содержание SIMATIC TDC

Отзывы:

Похожие инструкции для SIMATIC TDC

Бренды по названию

Популярные бренды