Siemens SCALANCE XP208EEC Скачать руководство пользователя страница 39

Страница: 39 / 96

Replacing a C-PLUG.

Removing a C-PLUG

1. Turn off the power to the device.

2. Loosen the screws of the cover.

3. Remove the cover.

4. Insert a screwdriver between the front edge of the C-PLUG (A) and the slot and release the C-

PLUG.

5. Remove the C-PLUG.

6. Close the cover (tightening torque =.8 Nm), to ensure that the device is closed and water and

dust proof.

Note
Loss of the configuration

The "RESET (Page 33)" button is located directly beside the slot for the C-PLUG. The button
cannot be used to remove the C-PLUG.

If you hold down the "RESET" button, you reset all settings of the device to the factory defaults.

Remove the C-PLUG with a screwdriver.

Description of the device

4.6 C-PLUG

SCALANCE XP-200
Operating Instructions, 03/2021, C79000-G8976-C428-08

Содержание SCALANCE XP208EEC

































































































Результаты поиска

Содержание SCALANCE XP208EEC

Отзывы:

Похожие инструкции для SCALANCE XP208EEC

Бренды по названию

Популярные бренды

Siemens SCALANCE XP208EEC, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE XP208EEC

Отзывы:

Похожие инструкции для SCALANCE XP208EEC

Бренды по названию

Популярные бренды