manualshive.com logo in svg

Siemens SCALANCE XP208EEC, Руководство по эксплуатации

Поделиться
Скачать
Siemens SCALANCE XP208EEC Скачать руководство пользователя страница 35

4.5

SELECT / SET button

NOTICE
Loss of water and dust protection

If the film of the button is damaged, the device is not water and dust proof.

Make sure that the film of the button does not get damaged. Do not use e.g. sharp objects to 
press the button.

Position

The "SELECT/SET" button is located on the front of the SCALANCE XP-200.

6(/(&7

6(7

Figure 4-2

SELECT/SET button

Setting the display mode

To set the required display mode, press the "SELECT/SET" button.

For more detailed information on the display modes, refer to the section "LEDs "DM1" and "DM2" 
(Page 29)".

Defining the fault mask

Using the fault mask, you specify an individual "good status" for the connected ports and the 
power supply. Deviations from this status are displayed as errors/faults.

You configure the monitoring of plugged-in connections in the plant engineering.

Description of the device

4.5 SELECT / SET button

SCALANCE XP-200
Operating Instructions, 03/2021, C79000-G8976-C428-08

35

Содержание SCALANCE XP208EEC

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды