Siemens SCALANCE XP208EEC Скачать руководство пользователя страница 81

Страница: 81 / 96

8.4

Technical specifications of the SCALANCE XP216PoE EEC

The following technical specifications apply to the SCALANCE XP216PoE EEC.

Technical specifications
Attachment to Industrial Ethernet

Quantity

Connector

M12 socket

Properties

D-/X-coded, half/full duplex; MDI-X pin
assignment, P5 - P8 and P13 - P16 with
Power over Ethernet

Transmission speed
• P1 - P8, P9, P11, P13 and P15
• P10, P12, P14 and P16

• 10 / 100 Mbps
• 10 / 100/ 1000 Mbps

Diagnostics interface
Serial interface

Quantity

Connector

M12 socket

Electrical data
Power supply

Rated voltage

54 VDC

Voltage range with PoE consumers type 1 46 to 57 VDC Safety Extra Low Voltage
Voltage range with PoE consumers type 2 52 to 57 VDC Safety Extra Low Voltage
Design

M12 socket, 4-pin

Cable cross-section

≥ 0.75 mm

(18 AWG)

Property

Implemented redundantly

Current consumption

At 54 VDC without PoE load

180 mA

At 54 VDC with max. PoE load

2500 mA

Effective power loss

At 54 VDC

10 W

At 54 VDC in PoE operation

13 W

Fusing

5 A / at least 60 V

PoE power per device

At 54 VDC

120 W

Permitted ambient conditions
Ambient temperature

During operation up to 2000 m

-40 °C to +70 °C

During storage

-40 ℃ to +70 ℃

During transportation

-40 ℃ to +70 ℃

Relative humidity

During operation at 25 ℃

≤ 95 % no condensation

Housing, dimensions and weight
Design

compact

Housing material

Aluminum

Degree of protection

IP 65

Dimensions (W x H x D)

200 x 280 x 49 mm (57 mm incl. protective caps)

Weight

2500 g

Installation options

• Wall mounting
• Back wall mounting
• Rack mounting

Technical specifications

8.4 Technical specifications of the SCALANCE XP216PoE EEC

SCALANCE XP-200
Operating Instructions, 03/2021, C79000-G8976-C428-08

Содержание SCALANCE XP208EEC

































































































Результаты поиска

Содержание SCALANCE XP208EEC

Отзывы:

Похожие инструкции для SCALANCE XP208EEC

Бренды по названию

Популярные бренды

Siemens SCALANCE XP208EEC, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE XP208EEC

Отзывы:

Похожие инструкции для SCALANCE XP208EEC

Бренды по названию

Популярные бренды