manualshive.com logo in svg

Siemens SCALANCE XP208EEC, Руководство по эксплуатации

Поделиться
Скачать
Siemens SCALANCE XP208EEC Скачать руководство пользователя страница 29

4.3.3

"SB" LED

The "SB" LED shows the status of the standby function.

LED color

LED status

Meaning

-

Off

The standby function is disabled.

Green

On

The standby function is enabled. The standby section is passive. 

Green

Flashing

The standby function is enabled. The standby section is active.

4.3.4

"F" LED

The "F" LED shows the fault/error status of the device.

Meaning during device startup 

LED color

LED status

Meaning during device startup

-

Off

Device startup was completed successfully.

Red

On

Device startup is not yet completed or errors have occurred.

Red

Flashing

There are errors in the firmware.

Meaning during operation

LED color

LED status

Meaning during operation

-

Off

The device is operating free of errors. The signaling contact is 
closed.

Red

On

The device has detected a problem. The signaling contact has 
opened.

4.3.5

LEDs "DM1" and "DM2"

The "DM1" and "DM2" LEDs indicate which display mode is set.

There are 5 display modes (A, B, C, D, and E). Display mode A is the default mode.

Depending on the set display mode, the "L1", "L2" LEDs and the port LEDs show different 
information.

LED color

LED status

Meaning

DM1 LED

DM2 LED

-

Off

Display mode A

Green

On

Off

Display mode B

Green

Off

On

Display mode C

Green

On

Display mode D

Green

Flashing

Off

Display mode E

Description of the device

4.3 LED display

SCALANCE XP-200
Operating Instructions, 03/2021, C79000-G8976-C428-08

29

Содержание SCALANCE XP208EEC

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды