manualshive.com logo in svg

Siemens SCALANCE XP208EEC, Руководство по эксплуатации

Поделиться
Скачать
Siemens SCALANCE XP208EEC Скачать руководство пользователя страница 32

Meaning in display mode B
In display mode B, the port LEDs indicate the transmission speed.

LED color

LED status

Meaning

-

Off

Port operating at 10 Mbps

Green

On

Port operating at 100 Mbps

Orange

On

Port operating at 1000 Mbps

If there is a connection problem and the type of transmission is fixed (autonegotiation off), the 
desired status, in other words the set transmission speed (1000 Mbps, 100 Mbps, 10 Mbps) 
continues to be displayed. If there is a connection problem and autonegotiation is active, the 
port LED goes off.

Meaning in display mode C
In display mode C, the port LEDs indicate the mode.

LED color

LED status

Meaning

-

Off

Port operating in half duplex mode

Green

On

Port operating in full duplex mode

Meaning in display mode D
In display mode D, the port LEDs indicate whether the port is monitored.

LED color

LED status

Meaning

-

Off

Port is not monitored.
If no link was established at the port the signaling contact 
does not indicate an error.

Green

On

Port is monitored.
If no link was established at the port the signaling contact 
indicates an error.

Meaning in display mode E
In display mode E, the port LEDs indicate whether the connected device is supplied using PoE.

LED color

LED status

Meaning

-

Off

The connected device is not supplied using PoE.

Green

On

The connected device is supplied via PoE.

Description of the device
4.3 LED display

SCALANCE XP-200

32

Operating Instructions, 03/2021, C79000-G8976-C428-08

Содержание SCALANCE XP208EEC

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды