Siemens RDG200KN Скачать руководство пользователя страница 46

Страница: 46 / 150

Functions
Additional functions

46 | 150

A6V11545892_en--_a

4.6.3 Output functions

The changeover sensor ensures changeover between heating and cooling mode

based on the acquired water temperature. We recommend activating the Purge

function (P251) with 2-port valves. This function ensures correct acquisition of the

medium temperature even if the 2-port valve is closed for an extended period of

time. The valve is opened for 1 to 5 minutes (adjustable) at 2-hour intervals during

off hours.
The function is valid for outputs PWM, On/Off, On/Off 3-wire, DC, 3-position and all

applications.
Limit the On/Off switching cycle to protect HVAC equipment, e.g., compressor and

reduce wear and tear. The minimum output on-time and off-time for the On/Off

control output can be adjusted from 1 to 20 minutes via P212 and P213. The

factory setting is 1 minute.
Readjusting the setpoint or heating/cooling mode changeover immediately results

in calculation of the output state; the outputs may not hold the minimum 1-minute

On/Off time.
If P212 or P213 is set to greater than 1 minute, the minimum On/Off time for the

control output is maintained as set, even if the setpoint or changeover mode is

readjusted.
For 2-pipe and 2-stage applications with different equipment, e.g., fan coil units

and radiant heating/cooling panels, it is possible to invert the sequence of the

equipment to optimize energy use, when the thermostat changes the sequence

from heating to cooling (P001 = 2 or 3).
Under factory settings, the 1

stage in heating (YHC1) is also the 1

stage in

cooling.
The swap function optimizes use of heating/cooling energy in mixed systems. E.g.,

when the fan coil units are combined with radiant heating/cooling panels, it is better

to start heating using the panels (1

stage heating, YHC1) and start cooling using

the fan coil unit (1

stage cooling, YHC2).

Enable the swap function by setting P254 (YHC2 output signal, 1

stage in cooling)

to ON, depending on the requested control signal.

Swap function disabled

Swap function enabled

P254 is set to OFF

P254 is set to ON

●

For 2-pipe/2-stage applications, see 2-pipe/2-stage heating or cooling [

➙

64].

●

If the equipment requests fan operation only in the 2

stage (heating and/or

cooling), see Fan control [

➙

84] to set up the fan function (fan in the 2

stage).

●

For application examples, see Swap function and/or fan in the 2nd stage

[

➙

137].

All heating sequences can also be used for floor heating.
You can use fan coil unit heating/cooling sequences for floor heating or cooling by

disabling the fan via P350.

Purge function (P251)

Minimum output On/Off

time (P212, P213)

Swap outputs for 2-pipe

and 2-stage applications

(P254)

Note

Floor heating/Floor cooling

(P350)

Содержание RDG200KN























































































































































Результаты поиска

Содержание RDG200KN

Отзывы:

Siemens RDG200KN, Основная документация, Страница: 46 / 150

Результаты поиска

Содержание RDG200KN

Отзывы: