manualshive.com logo in svg

Siemens micromaster 410, Руководство по эксплуатации, Страница: 78 / 84

Поделиться
Скачать
Siemens micromaster 410 Скачать руководство пользователя страница 78

Index

Issue 04/02

MICROMASTER 410    Operating Instructions

78

6SE6400-5EA00-0BP0

Index

A

Access Levels .......................................... 49
Altitude ..................................................... 19
Ambient operating conditions .................. 19
Applicable standards

European EMC Directive...................... 74
European Low Voltage Directive.......... 74
ISO 9001 .............................................. 74
Underwriters Laboratories.................... 74

Atmospheric pollution .............................. 20

B

Basic operation ........................................ 34

changing parameters with OP.............. 38
external motor thermal overload
protection........................................ 41, 43
general ................................................. 42
with OP................................................. 42

C

Changing the Line Supply Frequency...... 35
Commissioning ........................................ 31
Compound Braking .................................. 47
Contact address......................................... 5
Control Modes.......................................... 48

D

DC braking ............................................... 47
Default settings .................................. 34, 36
Dimensions and Torques......................... 23
DIN Rail Mounting.................................... 25
Drill pattern for MICROMASTER 410 ...... 22

E

Electrical Installation ................................ 26
Electro-Magnetic Compatibility

general ................................................. 69
self-certification .................................... 69
technical construction file ..................... 69

Electro-Magnetic Interference.................. 29

avoiding EMI......................................... 29

Electromagnetic radiation ........................ 20
EMC ......................................................... 69

EMC Directive Compliance ......................70
EMC performance

filtered for residential, commercial and
light industry..........................................72
filtered industrial class ..........................71
general industrial class .........................71

EMI ...........................................................29
External motor thermal overload protection

..............................................................43

F

Fault codes

with the Operator Panel fitted ...............57
with the Standard Inverter LED ............57

Faults and warnings

OP fitted................................................48
Standard Inverter ..................................48

Features ...................................................15
Fitting the Operator Panel ........................73
Flux Current Control .................................48
Foreword ....................................................5
Frequency Setpoint ..................................45
Front Panels .............................................33

H

Harmonic Currents

tables ....................................................21

Humidity Range........................................19

I

Installation ................................................17

after a period of storage .......................18

Installation and cooling.............................20
Internet Home Address ..............................5
Inverter block diagram..............................32

L

Linear V/f control ......................................48
Long cables

operation with .......................................27

M

Main characteristics..................................15
Mechanical Installation.............................22

Содержание micromaster 410





















































































Отзывы:

Нет отзывов