manualshive.com logo in svg

Siemens micromaster 410, Руководство по эксплуатации, Страница: 20 / 84

Поделиться
Скачать
Siemens micromaster 410 Скачать руководство пользователя страница 20

2  Installation

Issue 04/02

MICROMASTER 410    Operating Instructions

20

6SE6400-5EA00-0BP0

Shock

Do not drop the inverter or expose to sudden shock. Do not install the inverter in an
area where it is likely to be exposed to constant vibration.
Mechanical strength to EN 60721-3-3

Ø

  Deflection:

0.075 mm (10 ... 58 Hz)

Ø

 Acceleration:

10 m/s

2

 (58 ... 200 Hz)

Vibration

Do not install the inverter in an area where it is likely to be exposed to constant
vibration.

Electromagnetic Radiation

Do not install the inverter near sources of electromagnetic radiation.

Atmospheric Pollution

Do not install the inverter in an environment, which contains atmospheric pollutants
such as dust, corrosive gases, etc.

Water

Take care to site the inverter away from potential water hazards, e.g. do not install
the inverter beneath pipes that are subject to condensation. Avoid installing the
inverter where excessive humidity and condensation may occur.

Installation and cooling

CAUTION

The inverter can be front or side mounted, but 

MUST

 be installed in a vertical

position. Mount the inverter vertically to ensure optimum cooling, see Figure 2-5
on page 23.

Ensure that the inverter’s air vents are not obstructed. Allow 100 mm clearance
above and below the inverter. A clearance of 30 mm on both sides of the inverter is
also required.

Содержание micromaster 410





















































































Отзывы:

Нет отзывов