manualshive.com logo in svg

Siemens micromaster 410, Руководство по эксплуатации, Страница: 37 / 84

Поделиться
Скачать
Siemens micromaster 410 Скачать руководство пользователя страница 37

Issue 04/02

3  Commissioning

MICROMASTER 410    Operating Instructions
6SE6400-5EA00-0BP0

37

Buttons on the Operator Panel

Panel/Button

Function

Effects

Indicates

Status

The LCD displays the settings currently used by the converter.

Start motor

Pressing the button starts the converter. This button is
disabled by default. To enable this button set P0700 = 1.

Stop motor

OFF1

Pressing the button causes the motor to come to a
standstill at the selected ramp down rate. Disabled by
default; to enable set P0700 = 1.

OFF2

Pressing the button twice (or once long) causes the
motor to coast to a standstill.
This function is always enabled.

Change

direction

Press this button to change the direction of rotation of the
motor. Reverse is indicated by a minus (-) sign or a flashing
decimal point. Disabled by default, to enable set P0700 = 1.

Jog motor

Pressing this button while the inverter has no ON command
causes the motor to start and run at the preset jog frequency.
The motor stops when the button is released. Pressing this
button when the motor is running has no effect.

Functions

This button can be used to view additional information.
Pressing and holding the button for 2 seconds from any
parameter during operation, shows the following:
1. DC link voltage (indicated by d – units V).
2. Output frequency (Hz)
3. Output voltage (indicated by o – units V).
4. The value selected in P0005
Additional presses will toggle around the above displays.
A short press of the button will acknowledge a fault condition.

Jump Function

From any parameter (rXXXX or PXXXX) a short press of the
Fn button will immediately jump to r0000, you can then
change another parameter, if required. Upon returning to
r0000, pressing the Fn button will return you to your starting
point.

Access

parameters

Pressing this button allows access to the parameters.

Increase

value

Pressing this button increases the displayed value.

Decrease

value

Pressing this button decreases the displayed value.

Figure 3-5

Buttons on the Operator Panel

Содержание micromaster 410





















































































Отзывы:

Нет отзывов