manualshive.com logo in svg

Siemens micromaster 410, Руководство по эксплуатации, Страница: 39 / 84

Поделиться
Скачать
Siemens micromaster 410 Скачать руководство пользователя страница 39

Issue 04/02

3  Commissioning

MICROMASTER 410    Operating Instructions
6SE6400-5EA00-0BP0

39

NOTE

In some cases - when changing parameter values - the display on the Operator
Panel shows 

. This means the inverter is busy with tasks of higher priority.

Changing single digits in Parameter values

For changing the parameter value rapidly, the single digits of the display can be
changed by performing the following actions:
Ensure you are in the parameter value changing level (see "Changing parameters
with Operator Panel").
1. Press    (function button), which causes the right hand digit to blink.
2.  Change the value of this digit by pressing 

 / 

.

3. Press    (function button) again causes the next digit to blink.
4.  Perform steps 2 to 4 until the required value is displayed.

5. Press 

the   to leave the parameter value changing level.

NOTE

The function button may also be used to acknowledge a fault condition

3.2.4.2 

Quick commissioning (P0010=1)

It is 

important

 that parameter P0010 is used for commissioning and P0003 is used

to select the number of parameters to be accessed. This parameter allows a group
of parameters to be selected that will enable quick commissioning. Parameters
such as Motor settings and Ramp settings are included.
At the end of the quick commissioning sequence, P3900 should be selected,
which, when set to 1, will carry out the necessary motor calculations and clear all
other parameters (not included in P0010=1) to the default settings. This will only
happen in the Quick Commissioning mode.

Содержание micromaster 410





















































































Отзывы:

Нет отзывов