Siemens micromaster 410 Скачать руководство пользователя страница 59

Страница: 59 / 84

Issue 04/02

6 Troubleshooting

MICROMASTER 410 Operating Instructions
6SE6400-5EA00-0BP0

Fault

Possible Causes

Diagnose & Remedy

Reac-
tion

F0060
Asic Timeout

Internal communications failure

If fault persists, change inverter
Contact Service Department

OFF2

F0071
USS (BOP-
link) setpoint
fault

No setpoint values from USS during
telegram off time

Check USS master

OFF2

F0072
USS (COMM
link) setpoint
fault

No setpoint values from USS during
telegram off time

Check USS master

OFF2

F0085
External Fault

External fault triggered via terminal
inputs

Disable terminal input for fault trigger.

OFF2

F0101
Stack
Overflow

Software error or processor failure

Cycle through power (on/off).

Replace drive if fault is not corrected.

OFF2

F0450
BIST Tests
Failure
(Service Mode
Only)

Selftest failed

Drive may run but some features will not work

properly.

Replace

drive.

OFF2

Содержание micromaster 410





















































































Результаты поиска

Содержание micromaster 410

Отзывы:

Siemens micromaster 410, Руководство по эксплуатации, Страница: 59 / 84

Результаты поиска

Содержание micromaster 410

Отзывы: