Siemens micromaster 410 Скачать руководство пользователя страница 58

Страница: 58 / 84

6 Troubleshooting

Issue 04/02

MICROMASTER 410 Operating Instructions

6SE6400-5EA00-0BP0

6.3 Fault

messages

Fault

Possible Causes

Diagnose & Remedy

Reac-
tion

F0001
OverCurrent

Motor power (P0307) does not

correspond to the inverter power
(r0206)

Motor lead short circuit

Earth

faults

Check the following:
1. Motor power (P0307) must correspond to

inverter power (r0206).

2. Cable length limits must not be exceeded.
3. Motor cable and motor must have no short-

circuits or earth faults

4. Motor parameters must match the motor in

use

5. Motor must not be obstructed or overloaded.

Increase

the

ramp

time

Reduce the boost level

OFF2

F0002
OverVoltage

Overvoltage can be caused either

by too high main supply voltage
or if motor is in regenerative
mode.

Regenerative mode can be

caused by fast ramp downs or if
the motor is driven from an active
load.

Check the following:
1. Supply voltage (P0210) must lie within limits

indicated on the inverter rating plate.

2. DC-link voltage controller must be enabled

(P1240) and parameterized properly.

3. Ramp-down time (P1121) must match inertia

of load.

NOTE
Higher inertia requires longer ramp times

OFF2

F0003
UnderVoltage

Main

supply

failed.

Shock load outside specified

limits.

Check the following:
1. Supply voltage (P0210) must lie within limits

indicated on the inverter rating plate.

2. Supply must not be susceptible to temporary

failures or voltage reductions.

OFF2

F0004
Inverter Over
Temperature

Ventilation

inadequate

Ambient temperature is too high.

Check the following:
1. Pulse frequency must be set to default value
2. Ambient temperature could be higher than

specified for the inverter

OFF2

F0005
Inverter I

Inverter

overloaded.

Duty cycle too demanding.

Motor power (P0307) exceeds

inverter power capability ( r0206).

Check the following:
1. Load duty cycle must lie within specified

limits.

2. Motor power (P0307) must match inverter

power (r0206)

OFF2

F0011
Motor Over
Temperature
I

Motor overloaded

Check the following:
1. Load duty cycle must be correct
2. Motor temperatur warning level (P0604) must

match.

OFF1

F0041

Stator resistance measurement
failure

Check if the motor is connected to the

inverter.

Check that the motor data have been entered

correctly.

OFF2

F0051
Parameter
EEPROM Fault

Read or write failure while saving
non-volatile parameter.

Factory Reset and new parameterization
Change drive

OFF2

F0052
power stack
Fault

Read failure for power stack
information or invalid data.

Change drive

OFF2

Содержание micromaster 410





















































































Результаты поиска

Содержание micromaster 410

Отзывы:

Siemens micromaster 410, Руководство по эксплуатации, Страница: 58 / 84

Результаты поиска

Содержание micromaster 410

Отзывы: