manualshive.com logo in svg

Siemens micromaster 410, Руководство по эксплуатации, Страница: 71 / 84

Поделиться
Скачать
Siemens micromaster 410 Скачать руководство пользователя страница 71

Issue 04/02

9  Electro-Magnetic Compatibility

MICROMASTER 410    Operating Instructions
6SE6400-5EA00-0BP0

71

9.1.4 

General cases of EMC performance

Three General cases of EMC performance are available as detailed below:

Case 1: General Industrial

Compliance with the EMC Product Standard for Power Drive Systems EN 61800-3
for use in 

Second Environment (Industrial)

 and 

Restricted Distribution

.

Table 9-1

Case 1 - General Industrial

EMC Phenomenon

Standard

Level

Emissions:

Radiated Emissions

EN 55011

Level group 1, class A

Conducted Emissions

EN 61800-3

Limits are weaker as EN55011, class A,
group 1

Immunity:

Electrostatic Discharge

EN 61000-4-2

8 kV air discharge

Burst Interference

EN 61000-4-4

2 kV power cables (Level 3),
1 kV control (Level 3)

Radio Frequency Electromagnetic Field EN61000-4-3

26-1000 MHz, 10 V/m

Case 2: Filtered Industrial

This level of performance will allow the manufacturer/assembler to self-certify their
apparatus for compliance with the EMC directive for the industrial environment as
regards the EMC performance characteristics of the power drive system.
Performance limits are as specified in the Generic Industrial Emissions and
Immunity standards EN 50081-2 and EN 61000-6-2.

Table 9-2

Case 2 - Filtered Industrial

EMC Phenomenon

Standard

Level

Emissions:

Radiated Emissions

EN 55011

Level group 1, class A

Conducted Emissions

EN 61800-3

Level are weaker as EN55011 class A,
group 1

Immunity:

Supply Voltage Distortion

EN 61000-2-4

Voltage Fluctuations, Dips, Unbalance,
Frequency Variations

EN 61000-2-1

Electrostatic Discharge

EN 61000-4-2

8 kV air discharge

Burst Interference

EN 61000-4-4

2 kV power cables (Level 3),
2 kV control (Level 4)

Radio Frequency Electromagnetic
Field, amplitude modulated

EN 61000-4-3

80-1000 MHz, 10 V/m, 80% AM,
power and signal lines

Содержание micromaster 410





















































































Отзывы:

Нет отзывов