Siemens micromaster 410 Скачать руководство пользователя страница 57

Страница: 57 / 84

Issue 04/02

6 Troubleshooting

MICROMASTER 410 Operating Instructions
6SE6400-5EA00-0BP0

6 Troubleshooting

WARNING

♦

Repairs on equipment may only be carried out by

Siemens Service

, by repair

centers

authorized by Siemens

or by qualified personnel who are thoroughly

acquainted with all the warnings and operating procedures contained in this
manual.

♦

Any defective parts or components must be replaced using genuine Siemens
authorised parts.

♦

Risk of electric shock. The DC link capacitors remain charged for five minutes
after power has been removed.

It is not permissible to open the equipment

until 5 minutes after the power has been removed.

6.1

Troubleshooting with the Standard Inverter LED

The following is a description of the fault and warning indications given by the LED
on the Standard Inverter:

Inverter Off/No supply:

No LED lit.

Power On/Ready:

1000 ms On / 1000 ms Off

Inverter Running OK:

Steady LED

General Warning:

500 ms On / 200 ms Off

Fault Condition:

100 ms On / 100 ms Off

6.2

Troubleshooting with the Operator Panel (OP)

If the display shows a fault or warning code, please refer to Section 6.3.

If the motor fails to start when the ON command has been given:

Check that P0010 = 0.

Check that a valid ON signal is present.

Check that P0700 = 2 (for digital input control) or

P0700 = 1 (for OP control).

Check that the setpoint is present (0 to 10V on Terminal 7) or the setpoint has

been entered into the correct parameter, depending upon the setpoint source
(P1000). See the Parameter List for further details.

If the motor fails to run after changing the parameters, set P0010 = 30 then P0970
= 1 and press

to reset the inverter to the factory default parameter values.

Now use a switch between cobtrol terminals

and

. The drive should now run to

the defined setpoint by analogue input.

NOTICE

Motor data must relate to the inverter data power range and voltage.

Содержание micromaster 410





















































































Результаты поиска

Содержание micromaster 410

Отзывы:

Siemens micromaster 410, Руководство по эксплуатации, Страница: 57 / 84

Результаты поиска

Содержание micromaster 410

Отзывы: