Siemens micromaster 410 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 84

Siemens micromaster 410 Скачать руководство пользователя страница 22

2 Installation

Issue 04/02

MICROMASTER 410 Operating Instructions

22

6SE6400-5EA00-0BP0

2.6

Overvoltage and Trip Levels

The inverter will protect itself from both supply overvoltage and undervoltage. Trip
levels are show in Table 2-4. Internal overvoltage can occur during braking where
internal voltages are forced high by energy from an external load.

Table 2-4

Trip Levels

Input

Supplies

Undervoltage

trip levels

Overvoltage trip

levels

1 Phase 230 V

115 V

290 V

1 Phase 115 V

60 V

145 V

2.7 Mechanical

Installation

Warning

♦

THIS EQUIPMENT MUST BE GROUNDED.

♦

To ensure the safe operation of the equipment, it must be installed and

commissioned by qualified personnel in full compliance with the warnings laid
down in these operating instructions.

♦

Take particular note of the general and regional installation and safety

regulations regarding work on dangerous voltage installations (e.g. EN
50178), as well as the relevant regulations regarding the correct use of tools
and personal protective equipment (PPE).

♦

The mains input, DC and motor terminals, can carry dangerous voltages even

if the inverter is inoperative; wait

5 minutes

to allow the unit to discharge after

switching off before carrying out any installation work.

4

Figure 2-4

Dimensions of the MICROMASTER 410

«
...
20
21
22
23
24
...
»

Содержание micromaster 410





















































































Отзывы:

Нет отзывов