Siemens H-compact PLUS Скачать руководство пользователя страница 44

Страница: 44 / 83

Operation

8.6 Stoppages

WOGeneric TEAAC / 2008

Siemens AG Operating Instructions 1.03 1RQ671...-Z

8.6

Stoppages

Rolling-contact bearings

● Operate the motor regularly, at least once monthly, in the event of downtimes lasting

more than 1 month, for approximately one minute. Alternatively, turn the rotor as a

minimum. If a rotor shipping brace has been fitted to the machine, remove it before you

spin the rotor.

CAUTION
Damage to the bearings of rolling contact bearing motors when stored over a long

period.
Remaining in the same or almost the same position can damage the rolling contact

bearings.
Turn the rotor at the intervals specified. Ensure that the bearings then come to rest in a

position different from that they were in before. Use the feather key as a reference point.

● Please refer to the section "Energizing" before restarting the motor.

CAUTION
Storing rolling contact bearing motors for longer than six months
If the motor is not to be used for a period in excess of six months, suitable anti-

corrosion, mothballing, packaging and drying measures must be taken.

[ID 128.03.01]

Содержание H-compact PLUS




















































































Результаты поиска

Содержание H-compact PLUS

Отзывы:

Похожие инструкции для H-compact PLUS

Бренды по названию

Популярные бренды

Siemens H-compact PLUS, Руководство по эксплуатации

Результаты поиска

Содержание H-compact PLUS

Отзывы:

Похожие инструкции для H-compact PLUS

Бренды по названию

Популярные бренды