Siemens H-compact PLUS Скачать руководство пользователя страница 28

Страница: 28 / 83

Connection

6.1 Electrical connection

WOGeneric TEAAC / 2008

Siemens AG Operating Instructions 1.03 1RQ671...-Z

6.1.2

Terminal

designation

The following definitions apply to the terminal designations of three-phase machines in

accordance with DIN VDE 0530 Part 8 or IEC / EN 60034-8:

Table 6-3

Terminal designations using the 1U1-1 as an example

1 U 1 - 1 Designation
x

Index for pole assignment on pole-changing motors where applicable. A lower

index signifies a lower speed. Special case for split winding.

Phase designation U, V, W (IEC) T1, T2, T3 (NEMA)

Index for winding start (1) or end (2) or if there is more than one connection per

winding

x Additional index for cases in which it is obligatory to connect parallel power feed

cables to several terminals with otherwise identical designations

[ID: 332.02.01]

6.1.3

Direction of rotation

The technical specifications stipulate the following with respect to the motor connection:
●  Direction of rotation
●  The number and arrangement of the terminal boxes
●  The circuit and connection of the motor winding

Direction of rotation

On motors which are only allowed to run in one direction, the rating plate shows an arrow

which indicates the permitted direction of rotation, and it also specifies the terminal

connections in the required phase sequence.

IEC

NEMA

&ORFNZLVH

&RXQWHUFORFNZLVH

8 9 :

9 8 :

&ORFNZLVH

&RXQWHUFORFN

ZLVH

Direction of rotation of the motor when looking at the drive end

If you connect the power cables in the phase sequence L1, L2, L3 to U, V, W, the motor will

rotate clockwise. If two of the connections are swapped, then the motor will rotate

counterclockwise (e.g. L1, L2, L3 to V, U, W).

Note
If you want to run the motor in the opposite direction to the direction stated in the order,

please consult your contact partner at Siemens.
Rotational directions which may be required for application in a particular plant are not

shown on the rating plate. Please take these requirements into consideration when

connecting up the motor.

Содержание H-compact PLUS




















































































Результаты поиска

Содержание H-compact PLUS

Отзывы:

Похожие инструкции для H-compact PLUS

Бренды по названию

Популярные бренды

Siemens H-compact PLUS, Руководство по эксплуатации

Результаты поиска

Содержание H-compact PLUS

Отзывы:

Похожие инструкции для H-compact PLUS

Бренды по названию

Популярные бренды