Siemens H-compact PLUS Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 83

background image

Safety information

2.3 Switching high-voltage motors

WOGeneric TEAAC / 2008

10

Siemens AG Operating Instructions 1.03 1RQ671...-Z

Those responsible for plant safety must ensure the following:
● The basic planning work for the system and all work relating to transportation, assembly,

installation, commissioning, maintenance and repairs is carried out by qualified personnel

and checked by responsible, suitably skilled personnel.

● The operating instructions and machine documentation are always available.
● The technical data and specifications relating to installation, connection, ambient and

operating conditions are taken into account at all times.

●  The system-specific installation and safety regulations are observed.
●  Personal protective equipment is used.
●  Work on or in the vicinity of these machines by unqualified persons is prohibited.
●  If the machines are used outside industrial areas, the installation site must be

safeguarded against unauthorized access by means of suitable protection facilities (e.g.,

safety gates) and appropriate warning signs.

Note
Siemens Service Center
We recommend engaging the support and services of your local Siemens Service Center

(Page 69) for all planning, installation, commissioning, and maintenance work.

[ID 2.02]

2.3

Switching high-voltage motors

Switching overvoltages

If vacuum circuit breakers and vacuum contactors are used, what are known as multiple

restrikes can occur when the machine is switched off. This depends on various factors, such

as:
●  arc-extinguishing principle of the switch,
●  size of the motor,
●  length of the power supply cable,
●  system capacitance, etc.

CAUTION
Switching overvoltages
In some cases, multiple restrikes can result in switching overvoltages which are too high

for the insulation of the motor stator winding. This occurs when high-voltage motors with

starting currents I

A

≤ 600 A are disconnected during startup or following a blockage.

The peak voltages which arise as a result can damage the winding insulation.
If you are using vacuum circuit breakers and vacuum contactors, use an appropriate

surge suppressor, such as the Siemens 3EF (zinc oxide varistor with spark gap).

«
...
10
11
12
13
14
...
»

Содержание H-compact PLUS




















































































Отзывы:

Нет отзывов

Похожие инструкции для H-compact PLUS

Бренд: Daspi Страницы: 40

Бренд: Mitsubishi Страницы: 176

Бренд: BONFIGLIOLI Страницы: 20

Бренд: Rato Страницы: 32

Бренд: MAK Страницы: 2027

MerCruiser Diesel Inboard 2.8L

Бренд: Mercury Страницы: 93

Бренд: O.S. engine Страницы: 29

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 90

Бренд: Yamaha Страницы: 110

Бренд: Yamaha Страницы: 110

Бренд: Yamaha Страницы: 232

Бренд: Yamaha Страницы: 305

Бренд: Yamaha Страницы: 307

Бренд: Yamaha Страницы: 372

Бренд: Yamaha Страницы: 444

Бренд: Atlas Imperial Diesel Engine Страницы: 59

LZB 77 A0017-15

Бренд: Atlas Copco Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды