Siemens H-compact PLUS Скачать руководство пользователя страница 15

Страница: 15 / 83

WOGeneric TEAAC / 2008
Siemens AG Operating Instructions 1.03 1RQ671...-Z

Description

3.1

Applications

Overview

1RQ6 three-phase AC motors have been designed for a very wide range of drive

applications and also for energy conversion. They are characterized by their ruggedness,

long service life and reliability. They are also extremely versatile, allowing them to be tailored

to the particular function.
Details of the supplied motor and permissible operating conditions should be taken from this

documentation. [ID 6]

3.2

Design of the motor

The 1RQ6 motors are squirrel-cage, three-phase AC motors.

Supplementary devices

Temperature sensors are integrated in the stator winding to monitor the winding

temperature. Depending on the options ordered, various supplementary devices can be

installed or attached, e.g., anti-condensation heating in the stator housing or sensors to

monitor storage temperatures.

Construction standards

The motors comply with the following standards:

Table 3-1

Construction standards

Feature

Standard

Rating and performance

IEC / EN 60034-1

NEMA MG 1

Degree of protection

IEC / EN 60034-5

NEMA MG 1

Cooling

IEC / EN 60034-6

NEMA MG 1

Type of construction

IEC / EN 60034-7

NEMA MG 1

Noise emission

IEC / EN 60034-9

NEMA MG 1

Vibration severity grades

IEC / EN 60034-14

NEMA MG 1

Specifications for the degree of protection, cooling and type of construction can be taken

from the "Technical specifications" section of this documentation or from the rating plate on

the motor. [ID 1003.01]

Содержание H-compact PLUS




















































































Результаты поиска

Содержание H-compact PLUS

Отзывы:

Похожие инструкции для H-compact PLUS

Бренды по названию

Популярные бренды

Siemens H-compact PLUS, Руководство по эксплуатации

Результаты поиска

Содержание H-compact PLUS

Отзывы:

Похожие инструкции для H-compact PLUS

Бренды по названию

Популярные бренды