Siemens H-compact PLUS Скачать руководство пользователя страница 25

Страница: 25 / 83

Installation

5.4 Mounting

WOGeneric TEAAC / 2008
Siemens AG Operating Instructions 1.03 1RQ671...-Z

5.4

Mounting

Requirements

Preconditions for smooth, vibration-free operation:
●  Stable foundation design as per DIN 4024
●  Precision alignment of the motor
●  Correct balancing of parts to be fitted to the shaft end.
●  ISO 10816-3-compliant vibration velocity

Proceed as follows

● Use machine fixing bolts with the necessary strength class to ISO 898-1 (e.g. 10.9) for

reliable mounting and safe transmission of forces resulting from torque.

● When selecting the bolts and the design of the foundation, take into account the

maximum forces occurring in the case of a fault such as short circuit or system transfers

in phase opposition. The values for the foundation forces can be found in the configuring

documentation or are available on request from the manufacturer.

NOTICE
System-inherent frequencies
If the foundation has not been constructed correctly, frequencies that are inherent to the

foundation can occur after the machine set has been installed (system-inherent

frequencies). This can damage the machine set.
DIN 4024 must be taken into account when constructing the machine foundation.

[ID 15.04x]

Содержание H-compact PLUS




















































































Результаты поиска

Содержание H-compact PLUS

Отзывы:

Похожие инструкции для H-compact PLUS

Бренды по названию

Популярные бренды

Siemens H-compact PLUS, Руководство по эксплуатации

Результаты поиска

Содержание H-compact PLUS

Отзывы:

Похожие инструкции для H-compact PLUS

Бренды по названию

Популярные бренды