Siemens H-compact PLUS Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 83

background image

WOGeneric TEAAC / 2008
Siemens AG Operating Instructions 1.03 1RQ671...-Z

9

Safety information

2

2.1

Observing the five safety rules

For your personal safety and to prevent material damage when working on the device,

always observe the safety instructions on the product and the following five safety rules: You

must read the information provided in "Safety information".

The five safety rules:

1. isolate,
2. Protect against reconnection,
3. verify that the equipment is not live,
4. Ground and short circuit,
5. Cover or enclose adjacent components that are still live

Qualified personnel

Commissioning and operation of this machine are to be carried out by qualified personnel

only. For the purpose of the safety information in this Instruction Manual, a “qualified person”

is someone who is authorized to energize, ground, and tag equipment, systems, and circuits

in accordance with established safety procedures.

2.2

Safety and application instructions

The safe use of electrical machines

WARNING Ro-

tating or live parts
Rotating or live parts are dangerous.
Fatal or severe injuries and substantial material damage can occur if the required covers

are removed or if the machines are not handled, operated, or maintained properly.
Only remove covers in accordance with regulations and operate machines correctly.

Perform regular maintenance on the machine.

Qualified personnel

These operating instructions only contain the information that is necessary for the machines

to be used by qualified personnel in accordance with their intended purpose.

«
...
9
10
11
12
13
...
»

Содержание H-compact PLUS




















































































Отзывы:

Нет отзывов

Похожие инструкции для H-compact PLUS

Бренд: Northern Lights Страницы: 31

SEL Plus-RC Series

Бренд: Selve Страницы: 172

Бренд: ULPOWER Страницы: 25

Applied Motion Products TSM23XIP

Бренд: Moons' Страницы: 2

Бренд: Volvo Penta Страницы: 8

Бренд: Volvo Penta Страницы: 20

Бренд: JVL Страницы: 306

Бренд: JVL Страницы: 347

Бренд: Louvolite Страницы: 4

Бренд: Honda Страницы: 46

Бренд: DANA Страницы: 2

Бренд: Roto Страницы: 8

Бренд: O.S. engine Страницы: 38

Бренд: EMAK Страницы: 40

Бренд: Mitsubishi Страницы: 24

Бренд: Mitsubishi Страницы: 148

Бренд: Nanni Страницы: 12

RolloTube S-line Zip DoeFern

Бренд: RADEMACHER Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды