background image

Start-up 

7.2 Monitoring the temperature of the stator winding 

WOGeneric TEAAC / 2008       
Siemens AG Operating Instructions 1.03 1RQ671...-Z  

35

 

Limit values of the anti-condensation heating insulation resistance 

The insulation resistance of the anti-condensation heating with respect to the machine 

housing should not be lower than 1 MΩ when measured at 500 V DC. [ID 33.02] 

7.2

 

Monitoring the temperature of the stator winding 

Measures 

The connection cables include a current-dependent overload protection circuit. 
You can also monitor the temperature of the machine or the winding with the temperature 

sensors in the stator winding, which gives overload protection independent of the current.  

7.3

 

Measures to be performed prior to commissioning 

Overview 

Once the system has been correctly installed, you should check the following prior to 

commissioning: 
●  The machine has been properly installed and aligned. 
●  The machine is connected so that it rotates in the direction specified. 
●  The operating conditions correspond to the data specified on the rating plate. 
●  Any supplementary motor monitoring devices and equipment have been correctly 

connected and are fully functional. 

●  If bearing thermometers have been fitted, the bearing temperatures are checked during 

the initial run of the machine and the warning and shutdown values are set on the 

monitoring device. 

●  The output elements are correctly set, e.g.,: 

–  Couplings are aligned and balanced. 
–  The belt on the belt drive is tensioned. 
–  At the gear element, there is gear tooth flank and crest clearance. 
–  There is radial clearance. 

●  The minimum insulation resistance values and the minimum air gap values are observed. 
●  The grounding and equipotential bonding connections have been made correctly. 
●  Any bearing insulation has been fitted in accordance with the diagram. 
●  All fixing bolts, connecting elements, and electrical connections have been tightened to 

the specified torque. 

●  The rotor can spin without coming into contact with the stator. 
●  All touch protection measures for moving and live parts have been taken. 

Содержание H-compact PLUS




















































































Отзывы: