Siemens H-compact PLUS Скачать руководство пользователя страница 23

Страница: 23 / 83

WOGeneric TEAAC / 2008
Siemens AG Operating Instructions 1.03 1RQ671...-Z

Installation

5.1

Noise emission

When the motor is in operation, the A-weighted sound pressure level (measured in

accordance with ISO 1680) of 70 dB(A) is exceeded.
Take this into account when evaluating the noise levels at any operating personnel

workstations. If necessary take suitable noise protection measures.

5.2

Installation

Safety instructions

CAUTION
Heat-resistant components
The machine components can become hot during operation. Parts such as cable insulation

can be damaged by the high temperatures.
Only use heat-resistant parts. Temperature-sensitive parts such as normal cables or

electronic components must not be allowed to touch nor be attached to these parts.

Note the technical specifications provided in this documentation and on the plates on the

motor frame.

Removing the rotor shipping brace

If at all possible, wait to remove any rotor shipping braces until after the machine has been

set up.

Cooling

The cooling air must be able to be drawn in and discharged unimpeded; ensure that warm

discharged air is not drawn back in at the air intake.
● On the vertical motor design with air intake from above, the air inlets must be protected

against the ingress of foreign bodies and water. If the ventilation openings have louvered

covers, the openings must face downwards.

● In the case of internally cooled motors that are designed for pipe ventilation and/or

operation with a separately driven fan depending on the intended cooling method, pipes

and fan of an appropriate type of construction and rating must be connected.

● On motors with pipe ventilation, the cooling-air rate, direction of air flow and pressure

drop inside the motor are stated on the rating plate. Shipping covers on the ventilation

openings must be removed.

Содержание H-compact PLUS




















































































Результаты поиска

Содержание H-compact PLUS

Отзывы:

Похожие инструкции для H-compact PLUS

Бренды по названию

Популярные бренды

Siemens H-compact PLUS, Руководство по эксплуатации

Результаты поиска

Содержание H-compact PLUS

Отзывы:

Похожие инструкции для H-compact PLUS

Бренды по названию

Популярные бренды