Siemens ECO1-110/2 Скачать руководство пользователя страница 56

Страница: 56 / 137

ECO REFERENCE MANUAL

12-1

EMC

12.

EMC GUIDELINES

All electronic and electrical equipment generate

unwanted signals. These signals can be emitted

from the product either via cables that are

connected to the product (Input, output, control

signals etc.) or via electromagnetic radiation ‘radio

transmission’. These signals can be received by

other products (via the same routes) and can

interfere with the correct operation of the product.

Micromaster

Control

Output

Supply

Emissions

Micromaster

Control

Output

Supply

Immunity to

Emissions

Any particular product gives out a certain level of

emissions, and has a certain level of immunity to

incoming signals from other products. If the

immunity of all products is higher than their

emissions, there is no problem. If the immunity is

lower, severe problems can occur, causing quality

problems, damage, or in extreme cases injury.

Electro-magnetic Compatibility (EMC) concerns

how equipment works together; Electro-magnetic

Interference (EMI) refers to the unwanted signals

themselves.

EMI has become a more serious problem recently

as more electronic systems (which may prove to

have low immunity) are used in industrial

applications, and as power electronic products such

as drives, generate high frequency signals which

can produce high levels of interference.

ELECTRO-MAGNETIC
COMPATIBILITY (EMC)

All manufacturers/assemblers of electrical

apparatus which performs a complete intrinsic

function which is placed on the European market

as a single unit intended for the end user must

comply with the EMC directive EEC/89/336 after

January 1996. There are three ways by which the

manufacturer/assembler can demonstrate

compliance:

•

Self-Certification

This is a manufacturer's declaration that the

European standards applicable to the

electrical environment for which the apparatus

is intended have been met. Only standards

which have been officially published in the

Official Journal of the European Community

can be cited in the manufacturer's declaration.

•

Technical Construction File

A technical construction file can be prepared

for the apparatus describing its EMC

characteristics. This file must be approved by

a ‘Competent Body’ appointed by the

appropriate European government

organisation. This approach allows the use of

standards which are still in preparation.

•

EC Type-Examination Certificate

This approach is only applicable to radio

communication transmitting apparatus.

The MICROMASTER Eco and MIDIMASTER Eco

units do not have an intrinsic function until

connected with other components (e.g. a motor).

Therefore, the basic units are not allowed to be

CE marked for compliance with the EMC

directive. However, full details are provided of

the EMC performance characteristics of the

products when they are installed in accordance

with the wiring recommendations in the Wiring

Guidelines at the end of this section.

Содержание ECO1-110/2










































































































































Результаты поиска

Содержание ECO1-110/2

Отзывы:

Похожие инструкции для ECO1-110/2

Бренды по названию

Популярные бренды

Siemens ECO1-110/2, Справочное руководство

Результаты поиска

Содержание ECO1-110/2

Отзывы:

Похожие инструкции для ECO1-110/2

Бренды по названию

Популярные бренды