manualshive.com logo in svg

Siemens AGM60.4A9, Основная документация, Страница: 232 / 248

Поделиться
Скачать
Siemens AGM60.4A9 Скачать руководство пользователя страница 232

 

232/248 

Building Technologies Division 

Basic documentation LMV36... 

CC1P7544en 

Infrastructure & Citiies Sector 

30 Error code list 

25.09.2013 

Error 
code 

Diagnostic code 

Meaning for the LMV36... system 

Remedy 

12 # 

Valve 

proving 

 

 0 

Fuel valve 1 (V1) leaking 

(fuel valve 2 with valve proving via X5-01) 

For valve proving via X5-01 (gas pressure switch-min) 
- Check to see if the valve on the burner side is leaking 
- Check to see if the pressure switch for the valve proving is closed when gas pressure is present 
- Check wiring to see if there is a short-circuit 

 1 

Fuel valve 2 (V2) leaking 

(fuel valve 1 with valve proving via X5-01) 

For valve proving via X5-01 (gas pressure switch-min) 
- Check to see if the valve on the gas side is leaking 
- Check wiring to see if there is a short-circuit 

 

2 

Valve proving not possible 

Valve proving activated, but DWmin selected as input function for X9-04 (check parameters 238 
and 241) 

 

3 

Valve proving not possible 

Valve proving activated, but no input assigned (check parameters 236 and 237) 

 

4 

Valve proving not possible 

Valve proving activated, but 2 inputs assigned (set parameter 237 to DWmax or POC) 

 

5 

Valve proving not possible 

Valve proving activated, but 2 inputs assigned (check parameters 236 and 237) 

 

81 V1 

leaking 

Check to see if the valve on the gas side is leaking 
Check wiring to see if there is an open-circuit 

 

83 V2 

leaking 

Check to see if the valve on the burner side is leaking 
Check to see if the pressure switch for the leakage test is closed when gas pressure is present 
Check wiring for short-circuit 

14 # 

POC 

 

 0 

POC 

open 

Check to see if the valve’s closing contact is closed 

 1 

POC 

closed 

Check wiring 
Check to see if the valve’s closing contact opens when valve is controlled 

 

64 

POC open – prevention of startup 

Check wiring to see if there is a line interruption. 
Check to see if the valve’s closing contact is closed 

19

 

80 

Combustion pressure, POC – start prevention 

Check to see if pressure switch has closed with no combustion pressure present 
Check wiring for short-circuit 

20 #

 

Pressure switch-min (Pmin)

 

 

 

0

 

No minimum gas / oil pressure

Check wiring for line interruption 

 

1 

Gas shortage / prevention of startup 

Check wiring for line interruption 

21 

0 

Pressure switch-max (Pmax): Max. gas / oil pressure 

exceeded 

Check wiring to see if there is a line interruption. 

22 OFF S 

# 

Safety loop / burner flange 

 

 

0 

Safety loop / burner flange open 

 

 

1 

Safety loop / burner flange open / prevention of startup 

 

 

3 

Safety loop/burner flange, extraneous light – start prevention 

 

 

5 

Safety loop/burner flange, air pressure – start prevention 

 

 

17 

Safety loop/burner flange, combustion pressure – start 

 

Содержание AGM60.4A9

























































































































































































































































Отзывы:

Нет отзывов