manualshive.com logo in svg

Siemens AGM60.4A9, Основная документация, Страница: 140 / 248

Поделиться
Скачать
Siemens AGM60.4A9 Скачать руководство пользователя страница 140

 

140/248 

Building Technologies Division 

Basic documentation LMV36... 

CC1P7544en 

Infrastructure & Citiies Sector 

13 Fan control 

25.09.2013 

 

Value Error 

Remedy 

-22 

Air actuator not referenced 

Air actuator is not referenced or has lost its reference.

1. Check if the reference position can be approached. 
2. Check if actuators have been mixed up. 
3. If error only occurs after the start of standardization,  
    the actuator might be overloaded and cannot reach its 
    destination. 

-23 VSD 

deactivated 

Standardization was started with VSD deactivated 

 activate the VSD and repeat standardization 

-24 

No valid operation mode 

Standardization was started without valid operation 
mode 

 activate valid operation mode and repeat  

     standardization 

-25 

Pneumatic air-fuel ratio control 

Standardization was started with pneumatic air-fuel ratio 
control  

→

 standardization with pneumatic air-fuel ratio control is 

    not possible 

-128 

Running command with no preceding 
standardization 

VSD is controlled but not standardized  

 make standardization 

-255 

No standardized speed available 

Motor turns but is not standardized  

 make standardization 

 
The result of speed standardization (100% speed) can be read out via parameter. The 
speeds acquired by the 2 microcontrollers can differ by about 1.5%, the reason being 
slightly different resonator frequencies. 
 

No.

 

Parameter

642.0 Standardized 

speed 

Index 0 = speed 1 

642.1 Standardized 

speed 

Index 1= speed 2 (internal monitoring) 

 

13.12 Control of fan motor with pneumatic fuel-air 

ratio control

 

 

 
If control of the fan motor is employed for burners with pneumatic air-fuel ratio control, 
only the control path is used. There is no need to connect a speed feedback signal and 
to have speed control (for operating modes, refer to chapter 

Selection of operating 

mode

). 

 

Содержание AGM60.4A9

























































































































































































































































Отзывы:

Нет отзывов