Siemens AGM60.4A9 Скачать руководство пользователя страница 180

Страница: 180 / 248

180/248

Building Technologies Division

Basic documentation LMV36...

CC1P7544en

Infrastructure & Citiies Sector

28 Parameter level

25.09.2013

28.2 Entry of burner identification

The burner’s identification is entered like a password (character by character), but from right to left and
ending with «

».

h min s

ild

Parameter

113:

flashes.

Press

/reset

to go to editing mode.

/reset

h min s

ild

You are on the display for undefined burner
identification.
8 bars appear.

min s

1/0

Press

to select a number.

Example: Number

flashes.

/reset

min s

Press

/reset

to confirm the value.

Make the entry number by number.

min s

Press

to select the next number.

Example: Number

flashes.

/reset



/reset

min s

After entry of the last number, burner
identification must be confirmed by pressing

/reset

Содержание AGM60.4A9

























































































































































































































































Результаты поиска

Содержание AGM60.4A9

Отзывы:

Siemens AGM60.4A9, Основная документация, Страница: 180 / 248

Результаты поиска

Содержание AGM60.4A9

Отзывы: