Siemens AGM60.4A9 Скачать руководство пользователя страница 188

Страница: 188 / 248

188/248

Building Technologies Division

Basic documentation LMV36...

CC1P7544en

Infrastructure & Citiies Sector

28 Parameter level

25.09.2013

28.9 Parameter

with

index, with direct display

28.9.1 Using the example of parameter 501: No-flame positions fuel actuator

h min s

ild

/070

PArA

meter level

500:

for fuel-air ratio

control.

/reset

h min s

Press

/reset

to go to menu level

500:

Display: Parameter

501.

flashes, index

00:

and value

0.0

do not.

/reset

h min s

ild 77/

Press

/reset

to go to the index.

Display: Parameter

501.

does not flash, index

00:

flashes, value

0.0

does not.

h min s

ild 78/

Press

to select the required

index.

.00 = home position
.01 = prepurge position
.02 = postpurge position

Display: Index

01:

for prepurge position

flashes, value

0.0

does not.

/reset

h min s

ild 79/

Press

/reset

to go to editing mode.

Display: Value

0.0

h min s

ild 80/

Press

to select the required

prepurge position.

Example:

1.0

Содержание AGM60.4A9

























































































































































































































































Результаты поиска

Содержание AGM60.4A9

Отзывы:

Siemens AGM60.4A9, Основная документация, Страница: 188 / 248

Результаты поиска

Содержание AGM60.4A9

Отзывы: