Siemens AGM60.4A9 Скачать руководство пользователя страница 109 | Manualshive

Страница: 109 / 248

Siemens AGM60.4A9 Скачать руководство пользователя страница 109

109/248

Building Technologies Division

Basic documentation LMV36...

CC1P7544en

Infrastructure & Citiies Sector

11 Electronic fuel-air ratio control

25.09.2013

11 Electronic fuel-air ratio control

11.1 General

Electronic air-fuel ratio control is used to control the burner’s actuators depending on
burner output. It is possible to connect 2 actuators and, optionally, 1 VSD. Resolution is
0.1° with the actuators and 0.1% with the VSD. Output can be regulated in increments of
0.1% in modulating mode or with a maximum of 3 stages in multistage mode.
To reduce the electric power required for the actuators, they are never operated
simultaneously, but in successive order, or alternately.

11.2 Behavior

outside

the operating positions

Outside their operating positions, the actuators approach the different positions in
successive order. The program phase determines the position to be approached.

11.2.1 Traveling speed

The running speed of the actuators is fixed at 5 seconds for a positioning angle of 90°
for SQM33.4, SQM33.5, and SQN1.
The speed is 10 seconds for a positioning angle of 90° for SQM33.6.
The SQM33.7 requires 17 seconds for a positioning angle of 90°.

The ramp speed of the VSD can be adjusted separately for higher and lower speeds.

No. Parameter

522 Ramp

up

523 Ramp

down

The setting also applies to the operating position (refer to chapter

Operating position

).

11.2.2 Home position

This position is approached in the

Home run

(10),

Standby

(12) and

Lockout position

(00) phases.

The position can be set via the following parameters:

Parameter

Actuator

501.00

No-flame positions fuel actuator: Home position

502.00

No-flame positions air actuator: Home position

503.00

No-flame speeds VSD: No-load speed

504.00

Fuel 1: No-flame positions fuel actuator: Home position

505.00

Fuel 1: No-flame positions air actuator: Home position

506.00

Fuel 1: No-flame speeds VSD: No-load speed

«
...
107
108
109
110
111
...
»

Содержание AGM60.4A9

























































































































































































































































Отзывы:

Нет отзывов