Siemens AGM60.4A9 Скачать руководство пользователя страница 213

Страница: 213 / 248

213/248

Building Technologies Division

Basic documentation LMV36...

CC1P7544en

Infrastructure & Citiies Sector

28 Parameter level

25.09.2013

ESC

h min s

ild

156

The warm settings for fuel-air ratio control of the LMV36... have now been configured.

28.11.12 Cold settings for multistage mode («Lo 2-stage» and «Lo 3-stage»)



Note
Refer to chapters

Warm settings for «Lo 2-stage» and «Lo 3-stage»

But with no flame, no actuator travel and no automatic operation after the settings
have been made.

28.11.13 Intensity of flame during curve settings

When setting the curve and the curvepoint is displayed, you can press

/reset

to show the intensity of flame.

When pressing the button for >1 s, a change to parameter 954 is made; when releasing the button, you
return to the curvepoint.

h min s

ild 123

707

Example: Curvepoint

Low-flame position

P1.

/reset

>1 s

Change to parameter

954

Parameter

954:

flashes.

The intensity of flame in % is shown on the right.
Example:

954: 0.0

/reset

h min s

ild 123

707

Release

/reset

to return to curvepoint

Low-fire

position

P1.

Содержание AGM60.4A9

























































































































































































































































Результаты поиска

Содержание AGM60.4A9

Отзывы:

Siemens AGM60.4A9, Основная документация, Страница: 213 / 248

Результаты поиска

Содержание AGM60.4A9

Отзывы: