Shel lab SCO5W Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 62

Shel lab SCO5W Скачать руководство пользователя страница 60

60

|

P a g e

PARTS LIST

O

RDERING

P

ARTS AND

C

ONSUMABLES

If you have the Part Number for an item, you may order it directly from Sheldon Manufacturing by
calling 1-800-322-4897 extension 3. If you are not certain that you have the correct Part Number, or if
you need that specific item, please contact Sheldon Technical Support for help at 1-800-322-4897
extension 4 or (503) 640-3000. Please have the

model number

and

serial number

of the incubator

ready, as Tech Support will need this information to match your unit to its correct part.

A

CCESSORIES

The following accessories are available for the SCO5W.

CO

2

Cylinder Regulator, Dual Stage

For use with a gas supply cylinder (tank).

Part Number 7150509

Copper Shelf Assembly

Three copper shelves. Includes six copper shelf slides. Copper is known to have
antimicrobial properties.

Part Number: 9750582 complete assembly described above.

PN 5820504 Individual Shelf

PN 5820505 Individual Slide

«
...
58
59
60
61
62
»

Содержание SCO5W































































Отзывы:

Нет отзывов