Shel lab SCO5W Скачать руководство пользователя страница 53

Страница: 53 / 62

53 |

P a g e

USER MAINTENANCE

Continued next page

Calibration Continued

Place the incubator CO

display in its calibration mode.

Press and hold both the

and

DOWN

temperature arrow buttons simultaneously for

approximately 5 seconds.

Release the buttons when the temperature display

shows the letters “C O”. The display will then

begin flashing the current CO

display value.

Note:

If an arrow key is not pressed for five seconds, the

display will cease flashing, and store the last displayed
number as the CO

display value.

Use the

Down

arrows to adjust the current display

% value until it matches the reference device

concentration reading.

Reference Device



After matching the display to the reference device, wait 5
seconds.

•

The gas display will cease flashing and store

the corrected chamber display value.

•

The incubator will now begin injecting CO

allowing the current concentration to decay in

order to achieve the set point with the

corrected display value.

Decaying to Set Point

Allow the incubator sit for at last one 1 hour undisturbed to
stabilize

after the incubator has achieved the corrected

gas set point

•

Failure to wait until the incubator is fully

stabilized will result in an inaccurate reading.

Set Point Achieved

Содержание SCO5W































































Результаты поиска

Содержание SCO5W

Отзывы:

Shel lab SCO5W, Руководство по установке и эксплуатации, Страница: 53 / 62

Результаты поиска

Содержание SCO5W

Отзывы: