Shel lab SCO5W Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 62

Shel lab SCO5W Скачать руководство пользователя страница 45

45 |

P a g e

USER MAINTENANCE

G

AS

L

INES AND

HEPA

F

ILTERS

For the Optional Filtered Tubing Kit

The manufacturer recommends replacing in-line gas HEPA filters once per year or
when a filter is noticeably discolored.

•

HEPA filters are directional and must be installed facing in the correct direction.

•

The word “IN” is stamped on the rim of the filter assembly on the side that faces

toward the gas supply. See page 22.

Gas lines should be replaced when cracking, brittleness, permanent kinking, or other
signs of damage are present.

S

TORAGE OF THE

I

NCUBATOR

Perform the following steps if the incubator will be out of use for more than 24 hours to prevent
microbiological contamination such as fungus or mold.

Depower the incubator.

Disinfect and clean if required by your laboratory protocol, or if the chamber has been

exposed to pathogenic microorganisms.

Use a soft cloth to dry the chamber surfaces.

•

Do not place the incubator into storage while the chamber surfaces are damp.

M

AINTAINING

A

TMOSPHERIC

I

NTEGRITY

Periodically, inspect the door latch, trim, catch, and gaskets for signs of deterioration. Failure to
maintain the integrity of the door system shortens the life span of the incubator.

E

LECTRICAL

C

OMPONENTS

Electrical components do not require maintenance. If the incubator fails to operate as specified,
please contact your distributor or

Technical Support

for assistance (please see page 8).

“IN”

In-Line Gas Filter

«
...
43
44
45
46
47
...
»

Содержание SCO5W































































Отзывы:

Нет отзывов