Shel lab SCO5W Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 62

Shel lab SCO5W Скачать руководство пользователя страница 35

35 |

P a g e

OPERATION

M

UTING THE

A

UDIBLE

T

EMPERATURE

A

LARM

Audible and visual deviation alarms activate if the incubation chamber
temperature deviates by 1

°

C above or below the temperature set point.

The low deviation audible alarm has a delay of 15 minutes to prevent the
low audible from sounding each time the doors are opened, causing a
short-lived drop in temperature.

To mute an audible high or low deviation alarm:

Press and hold either the

Up

or

Down

arrow on the Temperature

Control until the amber Mute LED illuminates and the audible alarm

shuts off.

•

The audible alarm will remain muted for the duration of the
current temperature deviation.

•

The visual alarm indicator will remain illuminated.

•

Any

new

deviation of ±1°C or greater will reactivate the audible

alarm.

A

UTOMATIC

D

OOR

C

UTOFF

Gas, heating, and air circulation pause.

Whenever the incubation chamber door is opened, the incubator automatically stops the flow of CO

2

into the chamber, depowers the heater element, and ceases operation of the internal blower fan.
This limits the amount of CO

2

released into the workspace around the incubator. It also prevents the

heater from attempting to counteract the continual inflow of cooler air, which would cause a
significant heat spike once the door is closed. Normal CO

2

injections, heating, and fan operation all

resume automatically when the outer door is closed.

Figure 2: High

Alarm Muted

«
...
33
34
35
36
37
...
»

Содержание SCO5W































































Отзывы:

Нет отзывов