Shel lab SCO5W Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 62

Shel lab SCO5W Скачать руководство пользователя страница 27

27 |

P a g e

CONTROL PANEL OVERVIEW

Control Panel

Power Switch

Power is supplied when the switch is in the ( I ) on position.

Set Over Temperature

This graduated dial sets the Over Temperature Limit system heating cut off point. The OTL system
helps prevents unchecked heating of the incubation chamber in the event the main temperature
control system fails. For more details, please see the

Over Temperature Limit System

description on

The red Over Temp Activated light illuminates when the Over Temperature Limit system cuts off
heating to the incubation chamber by rerouting power away from the heating elements.

Temperature Control and Display

During normal operations, the Set Temperature display shows the current incubation chamber air
temperature, accurate to 0.1°C. The Up and Down buttons are used to change display modes and
then input either a new temperature set point or a calibration adjustment. The display blinks
continually while in its set point or calibration adjustment modes, preceded by an “SP” for Set Point
or “C O” for calibration offset.

Red LED alarm indicators marked High and Low illuminate whenever the temperature deviates by
±1°C or greater from the current set point. The yellow LED marked Mute illuminates whenever an
audible deviation alarm is being muted. See the

Muting the Audible Temperature Alarm

entry on

page 35 for more information.

The green indicator labeled Heating Activated illuminates whenever the temperature control system
is heating the incubation chamber.

«
...
25
26
27
28
29
...
»

Содержание SCO5W































































Отзывы:

Нет отзывов