Shel lab SCO5W Скачать руководство пользователя страница 16

Страница: 16 / 62

P a g e

INSTALLATION

EQUIRED

MBIENT

ONDITIONS

These units are intended for use

indoors

, at room temperatures between

C and 30

C (59

F and 86

at no greater than

80% Relative Humidity

(at 25

C / 77

F). Operating outside these conditions may

adversely affect its incubator temperature stability and effective operating range.

EQUIRED

LEARANCES

These clearances are required to provide air flows sufficient for ventilation and cooling.

4 inches (102mm)

of clearance is required on the sides and back.

2 inches (51mm)

of headspace clearance between the top of the unit and any overhead partitions.

NVIRONMENTAL

ISRUPTION

OURCES

When selecting a location to install the unit, look for sources of heat, cold, and moving air that can affect
the chamber temperature and atmospheric integrity:

•

Ovens, autoclaves, and any device that produces significant radiant heat

•

High-traffic areas

•

Direct sunlight

•

Heating and cooling ducts or other sources of fast-moving air currents

2” (51mm)

4” (102mm)

Access Port

2” (51mm)

4” (102mm)

Door Swing

23.5“ (597mm)

Power Cord

Gas Connections

Содержание SCO5W































































Результаты поиска

Содержание SCO5W

Отзывы:

Shel lab SCO5W, Руководство по установке и эксплуатации, Страница: 16 / 62

Результаты поиска

Содержание SCO5W

Отзывы: