Shel lab SCO5W Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 62

Shel lab SCO5W Скачать руководство пользователя страница 46

46

|

P a g e

USER MAINTENANCE

R

EPLACE THE

C

HAMBER

HEPA

F

ILTER

Always turn off and unplug the incubator before carrying out this procedure.

Replace the filter at least once per year, or when the filter is noticeably discolored.

Exercise caution

when removing the ceiling air duct. A plastic blower fan and the fragile head of the

temperature and CO

2

sensors are located just above the duct and just to the right of the duct.

Dismount the ceiling air duct, using firm but careful pressure to remove the duct feet from the

tops of the shelf standards.

Remove the duct from the chamber.

Remove the black plastic cap from the HEPA filter by pulling down on it.

Remove the old HEPA filter by pulling down. It will snap out without difficulty.

Snap the new HEPA filter into position on the duct. It may be necessary to tilt the filter slightly

to one side.

See the Installing the

Chamber Air Duct and HEPA

filter on page 20 for detailed instructions on

reinstalling the filter and duct.

Step 1

Step 2

Step 3

Step 4

Back

Front

Ceiling Duct

HEPA Filter with

«
...
44
45
46
47
48
...
»

Содержание SCO5W































































Отзывы:

Нет отзывов