Shel lab SCO5W Скачать руководство пользователя страница 54

Страница: 54 / 62

P a g e

USER MAINTENANCE

End of procedure

Calibration Continued

Compare the reference device reading with the incubator CO

display again.

•

If the reference device and the incubator display readings

are the same or the difference falls within the range of your

protocol,

the incubator is now calibrated for CO

-OR-

•

See the next step if the readings fail to match or fall outside

of your protocol range.

Reference Device



If the two readings are not the same, and the difference still falls
outside the acceptable range of your protocol, repeat steps 3 – 7
up to two (2) more times.

•

Three (3) calibration attempts may be required to

successfully calibrate units that are more than ±2% out

of calibration.

Reference Device



Contact your distributor or technical support for assistance if the gas concentration readings
of the incubator CO

display and the reference device still fall outside your protocol after three

calibration attempts.

Содержание SCO5W































































Результаты поиска

Содержание SCO5W

Отзывы:

Shel lab SCO5W, Руководство по установке и эксплуатации, Страница: 54 / 62

Результаты поиска

Содержание SCO5W

Отзывы: